| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: rockchip: rockchip_pdm: Handle runtime PM resume failures in set_fmt
rockchip_pdm_set_fmt() calls pm_runtime_get_sync() before accessing
hardware registers, but ignores its return value.
If the runtime resume fails, the function continues to perform register
accesses while the device state is undefined.
Replace pm_runtime_get_sync() with pm_runtime_resume_and_get() and
return early on failure to avoid unpowered register accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: xgmac2: disable RBUE in default RX interrupt mask
Enabling the RX Buffer Unavailable (RBUE) interrupt is counterproductive
and can trigger a MAC interrupt storm under heavy RX pressure. When the
DMA runs out of RX descriptors it fires RBUE continuously until software
refills the ring.
However, RBUE is redundant: the normal RX completion interrupt (RIE)
already triggers NAPI, which processes completed descriptors and refills
the ring, causing the DMA to resume. The RBUE handler itself only sets
handle_rx - the same outcome as RIE.
On Agilex5 under heavy RX pressure, the MAC interrupt (which includes
RBUE) was observed firing 1,821,811,555 times against only 2,618,627
actual RX completions - a ~695x ratio - confirming the severity of the
storm.
RBUE does not provide OOM recovery. If page_pool is exhausted,
stmmac_rx_refill() cannot advance the DMA tail pointer, the DMA stays
suspended, and RBUE fires again on the next NAPI completion - a storm
with no forward progress. This patch trades that storm for a clean
stall with the same RX outcome. Proper OOM recovery is a pre-existing
gap outside the scope of this fix.
Note: as a consequence of disabling RBUE, the rx_buf_unav_irq ethtool
counter will always read 0 on XGMAC2 devices. This behaviour is already
inconsistent across DWMAC core versions.
Remove RBUE from XGMAC_DMA_INT_DEFAULT_EN and XGMAC_DMA_INT_DEFAULT_RX
to prevent the interrupt storm while keeping normal RX handling intact. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix races in cifsd thread creation
The cifsd demultiplex thread can run and access tcp_ses before the parent
thread has finished populating tcp_ses, which the worker thread accesses
locklessly.
Also, the kthread_run macro may start the thread before returning the
thread pointer. Because the pointer is part of the structure that the
thread can access, if the kernel is preempted after the thread is spawned,
but before the thread pointer is populated and the thread attempts to exit,
it will sleep, waiting for a SIGKILL signal.
Fix this by moving creation of the thread to after all of tcp_ses'es
fields are populated, and spawning the thread last, using a split
kthread_create/wake_up_process logic. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix handling of damaged volume in exfat_create_upcase_table()
When the size of the upcase table is set to zero in the dentry for any
reason(e.g. corrupted media or misbehaving device), an integer overflow
causes the module to loop indefinitely.
If the size of the upcase table is read zero, do not attempt to load the
table. Instead, fallback to loading the default upcase table. If the
size of the upcase table is zero or no upcase table is found, raise
exfat_fs_error() to mark the volume read-only. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-fs: avoid double-free on failed queue setup
virtio_fs_setup_vqs() allocates fs->vqs and fs->mq_map before calling
virtio_find_vqs(). If virtio_find_vqs() fails, the error path frees both
pointers and returns an error to virtio_fs_probe().
virtio_fs_probe() then drops the last kobject reference, and
virtio_fs_ktype_release() frees fs->vqs and fs->mq_map again. This leaves
dangling pointers in struct virtio_fs and can trigger a double-free during
probe failure cleanup.
Set fs->vqs and fs->mq_map to NULL immediately after kfree() in the
virtio_fs_setup_vqs() error path so that the later kobject release sees an
uninitialized state and kfree(NULL) becomes harmless.
This can be reproduced when a broken virtio-fs device advertises more
request queues than the transport actually provides. In that case
virtio_find_vqs() fails while setting up the extra queue, and the probe
path reaches the double-free cleanup sequence. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: hidpp: fix potential UAF in hidpp_connect_event()
If input_register_device() fails, we call input_free_device(), but keep
stale pointer to the old device in hidpp->input, which could potentially
lead to UAF. Fix that by resetting it to NULL before returning from
hidpp_connect_event(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: Add NULL check for spi_get_device_id() in spi_get_device_match_data()
Prevent NULL pointer dereference when spi_get_device_id() returns NULL,
which can happen when using driver_override without matching SPI ID entry. |
| In the Linux kernel, the following vulnerability has been resolved:
tls: reject the combination of TLS and sockmap
TLS and sockmap (BPF psock) integration hides a lot of latent bugs.
Bugs which may be more or less relevant for real users but they
are definitely exploitable.
We could not find anyone actively using this integration so let's
reject this config. Adding a TLS socket to a sockmap was already
rejected by sk_psock_init() through the inet_csk_has_ulp() check.
We need to reject the attempts to configure the TLS keys (rather
than adding the ULP itself) because checking prior to the ULP
installation is tricky without risking a race with sockmap getting
added in parallel (sockmap does not hold the socket lock).
This patch is a minimal rejection of the feature. Subsequent patch
in the series will do a light dead code removal. Full cleanup would
require a major rewrite of the Tx path, we don't need skmsg any more. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Let driver decide buffer size at AMDKFD_IOC_GET_DMABUF_INFO ioctl
amdkfd driver needs allocate buffer to return bo metadata to user space. The
buffer size is controlled by user currently. It is a potential security issue
that hostile value (e.g. 2 GiB) lets any render-group user trigger order-MAX
allocation/OOM in kernel context.
This patch first finds bo metadata size. If the size is smaller than user
provided value drive can safely allocate buffer in kernel space and copy to
user space buffer. If not, driver will let user know, not allocate and copy.
User will redo with new buffer in user space.
This patch lets driver decide buffer allocation size to avoid potential hostile
size from user space.
(cherry picked from commit f54ce9e8cbd3abe0eda3a285f54dc4f572fe589a) |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: iproc: Protect root bus removal with rescan lock
Hold the pci_rescan_remove_lock lock while stopping and removing a root bus
to avoid racing with concurrent rescan or hotplug operations triggered via
sysfs. Such races may lead to use-after-free issues or system crashes.
[bhelgaas: commit log] |
| An out-of-bounds read in libXi's XI2 class parsing via size_classes() and copy_classes() in libXi before 1.8.4 could be used by malicous servers to crash the X client. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: altera: Protect root bus removal with rescan lock
Hold the pci_rescan_remove_lock lock while stopping and removing a root bus
to avoid racing with concurrent rescan or hotplug operations triggered via
sysfs. Such races may lead to use-after-free issues or system crashes.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: rockchip: Protect root bus removal with rescan lock
Hold the pci_rescan_remove_lock lock while stopping and removing a root bus
to avoid racing with concurrent rescan or hotplug operations triggered via
sysfs. Such races may lead to use-after-free issues or system crashes.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: mediatek: Protect root bus removal with rescan lock
Hold the pci_rescan_remove_lock lock while stopping and removing a root bus
to avoid racing with concurrent rescan or hotplug operations triggered via
sysfs. Such races may lead to use-after-free issues or system crashes.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: plda: Protect root bus removal with rescan lock
Hold the pci_rescan_remove_lock lock while stopping and removing a root bus
to avoid racing with concurrent rescan or hotplug operations triggered via
sysfs. Such races may lead to use-after-free issues or system crashes.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix addr_filter_ranges lifetime
Lee Jia Jie reported that since event::addr_filter_ranges is used
under RCU, it should be RCU freed. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: validate inline dentry name lengths before conversion
Inline dentry conversion copies names out of the inline dentry area
before checking that each recorded name length fits in the available
filename slots.
A corrupted image can therefore make the conversion path read past
the inline filename storage while building the regular dentry block.
Validate each inline dentry name length against the inline filename
area before copying it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: au1000: move free_irq out of the close-time spinlocked section
au1000_close() calls free_irq() while aup->lock is still held with
spin_lock_irqsave(). free_irq() can sleep because it takes the IRQ
descriptor request mutex, so it does not belong inside the close-time
spinlocked section.
This was found by our static analysis tool and then confirmed by manual
review of the in-tree au1000_close() .ndo_stop path. The reviewed path
keeps aup->lock held across the MAC reset, queue stop and
free_irq(dev->irq, dev).
A directed runtime validation kept that ndo_stop carrier and the same
free_irq(dev->irq, dev) operation under the driver lock. Lockdep reported
"BUG: sleeping function called from invalid context" and "Invalid wait
context" while free_irq() was taking desc->request_mutex, with
au1000_close() and free_irq() on the stack.
Drop aup->lock before freeing the IRQ. The protected close-time work still
stops the device and queue before IRQ teardown, but the sleepable IRQ core
path now runs outside the spinlocked section. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: core: Abort active target transfer on controller suspend
When an SPI controller operating in target mode has a transfer in
progress at the time of system suspend, the suspend path proceeds
without aborting the ongoing transfer. This can leave the hardware in
an inconsistent state, potentially causing the system to hang or fail
to resume cleanly.
Fix this by invoking the controller's target_abort callback from
spi_controller_suspend() when the controller is in target mode and the
callback is registered. This ensures any active target transfer is
cleanly terminated before the controller is suspended. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: tree-checker: validate INODE_REF's namelen
[BUG]
A crafted btrfs image can trigger the following crash:
BUG: unable to handle page fault for address: ffffd1dc42884000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
CPU: 9 UID: 0 PID: 1034 Comm: poc Not tainted 7.1.0-rc4-custom+ #383 PREEMPT(full) 46af0a92938a63be7132e0dfd71e62327c51d5c2
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:memcpy+0xc/0x10
Call Trace:
<TASK>
read_extent_buffer+0xe4/0x100 [btrfs 3cf0785dd58fec8c5ff84633b772f17ce1f92a8f]
btrfs_get_name+0x15e/0x1e0 [btrfs 3cf0785dd58fec8c5ff84633b772f17ce1f92a8f]
reconnect_path+0x165/0x390
exportfs_decode_fh_raw+0x337/0x400
? drop_caches_sysctl_handler+0xb0/0xb0
</TASK>
---[ end trace 0000000000000000 ]---
RIP: 0010:memcpy+0xc/0x10
Kernel panic - not syncing: Fatal exception
[CAUSE]
TThe crafted image has the following corrupted INODE_REF item:
item 9 key (258 INODE_REF 257) itemoff 11544 itemsize 4106
index 2 namelen 4096 name: d\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000
The itemsize matches the namelen, but the namelen is 4096, way larger
than normal name length limit (BTRFS_NAME_LEN, 255).
Meanwhile the memory of the @name is only 255 byte sized, this will cause
out-of-boundary access, and cause the above crash.
[FIX]
Add extra namelen verification for INODE_REF, just like what we have
done in ROOT_REF checks.
Now the crafted image can be rejected gracefully:
BTRFS critical (device dm-2): corrupt leaf: root=5 block=30572544 slot=14 ino=259, invalid inode ref name length, has 4096 expect [1, 255]
BTRFS error (device dm-2): read time tree block corruption detected on logical 30572544 mirror 2
[ Rebase, add a Link: tag, add an simple cause analyze ] |
