| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx9: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit b71604f8685b0eba07866f4e8dc30f93e1931054) |
| In the Linux kernel, the following vulnerability has been resolved:
mpls: fix NULL deref in mpls_valid_fib_dump_req() on CONFIG_INET=n
On CONFIG_INET=n builds, mpls_valid_fib_dump_req() walks the parsed
attribute table itself instead of calling ip_valid_fib_dump_req(). The
RTA_OIF arm passes tb[RTA_OIF] to nla_get_u32() without checking it is
present, so an RTM_GETROUTE dump for AF_MPLS with strict checking and no
RTA_OIF hits a NULL dereference.
RTM_GETROUTE is RTNL_KIND_GET, which rtnetlink_rcv_msg() permits without
CAP_NET_ADMIN, so an unprivileged user can trigger it.
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:mpls_valid_fib_dump_req (net/mpls/af_mpls.c:2189)
Call Trace:
mpls_dump_routes (net/mpls/af_mpls.c:2236)
netlink_dump (net/netlink/af_netlink.c:2331)
__netlink_dump_start (net/netlink/af_netlink.c:2446)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7033)
netlink_rcv_skb (net/netlink/af_netlink.c:2556)
netlink_unicast (net/netlink/af_netlink.c:1345)
netlink_sendmsg (net/netlink/af_netlink.c:1900)
__sock_sendmsg (net/socket.c:790)
____sys_sendmsg (net/socket.c:2684)
___sys_sendmsg (net/socket.c:2738)
__sys_sendmsg (net/socket.c:2770)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Skip unset attributes, as ip_valid_fib_dump_req() does. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: ndisc: fix NULL deref in accept_untracked_na()
accept_untracked_na() re-fetches the inet6_dev with __in6_dev_get(dev)
and dereferences idev->cnf.accept_untracked_na without a NULL check,
even though its only caller ndisc_recv_na() already fetched and
NULL-checked idev for the same device.
Both reads of dev->ip6_ptr run in the same RCU read-side critical
section, but a concurrent addrconf_ifdown() can clear dev->ip6_ptr
between them: lowering the MTU below IPV6_MIN_MTU calls addrconf_ifdown()
without the synchronize_net() that orders the unregister path, so the
re-fetch returns NULL and oopses:
BUG: KASAN: null-ptr-deref in ndisc_recv_na (net/ipv6/ndisc.c:974)
Read of size 4 at addr 0000000000000364
Call Trace:
<IRQ>
ndisc_recv_na (net/ipv6/ndisc.c:974)
icmpv6_rcv (net/ipv6/icmp.c:1193)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:479)
ip6_input_finish (net/ipv6/ip6_input.c:534)
ip6_input (net/ipv6/ip6_input.c:545)
ip6_mc_input (net/ipv6/ip6_input.c:635)
ipv6_rcv (net/ipv6/ip6_input.c:351)
</IRQ>
It is reachable by an unprivileged user via a network namespace.
Pass the caller's already validated idev instead of re-fetching it; the
idev stays alive for the whole RCU critical section, so it is safe even
after dev->ip6_ptr has been cleared. |
| When handling the filename directive in the Content-Disposition header, the filename would be truncated if the filename contained a NULL character. This could have led to reflected file download attacks potentially tricking users to install malware. This vulnerability affects Firefox < 112, Focus for Android < 112, Firefox ESR < 102.10, Firefox for Android < 112, and Thunderbird < 102.10. |
| kin-openapi is a Go project for handling OpenAPI files. From 0.2.0 until 0.144.0, openapi3filter.ValidateRequest can encounter a NULL-pointer-dereference denial of service when an operation declares a content parameter whose application/json media type has no schema. In openapi3filter/req_resp_decoder.go, the default defaultContentParameterDecoder dereferences mt.Schema.Value without checking whether mt.Schema is nil, even though doc.Validate() accepts the document under OpenAPI 3.0.x and 3.1.x. A single unauthenticated request supplying the parameter value can panic request validation, causing an aborted request with log growth in the common synchronous net/http path or a full process crash in integrations without recovery. This issue is fixed in version 0.144.0. |
| HDF5 contains a NULL pointer dereference vulnerability. Processing a crafted HDF5 file containing an attribute with an invalid variable-length datatype type field may cause the application to crash when the attribute is read. |
| A vulnerability was detected in TOTOLINK EX1200L 9.3.5u.6146_B20201023. This affects the function setWizardCfg of the file /cgi-bin/cstecgi.cgi. The manipulation results in null pointer dereference. The attack can be launched remotely. The exploit is now public and may be used. |
| A flaw was found in 389 Directory Server. The dereference control plugin does not check for allocation failure before using a BER structure, allowing an unauthenticated remote attacker to crash the LDAP server when the system is under memory pressure. |
| A security vulnerability has been detected in TOTOLINK EX1200L 9.3.5u.6146_B20201023. Affected by this issue is the function setPasswordCfg of the file /cgi-bin/cstecgi.cgi of the component Password Configuration Handler. The manipulation leads to null pointer dereference. The attack can be initiated remotely. The exploit has been disclosed publicly and may be used. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix null pointer dereference in proc_show_files()
When a SMB2 client opens a file with a durable v2 handle and then issues
SMB2 SESSION_LOGOFF, session_fd_check() clears fp->tcon = NULL on the
reconnectable file pointer but leaves the fp registered in global_ft.idr
until the durable scavenger fires (up to fp->durable_timeout seconds
later).
During that window any read of /proc/fs/ksmbd/files (mode 0400) panics
the kernel because proc_show_files() walks global_ft.idr and
unconditionally dereferences fp->tcon->id with no NULL guard.
Reproducer requires only a successful SMB2 SESSION_SETUP and a share
configured with 'durable handles = yes'. KASAN report on mainline
70390501d194:
general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:proc_show_files+0x118/0x740
Call Trace:
proc_show_files+0x118/0x740
seq_read_iter+0x4ef/0xe10
proc_reg_read_iter+0x1b7/0x280
...
Guard the dereference. A durable-disconnected fp legitimately has no
tcon; report its tree id as 0 rather than oopsing. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix null pointer dereference in compare_guid_key()
session_fd_check() walks the per-inode m_op_list during durable-handle
session teardown and sets op->conn = NULL for every opinfo whose conn
matched the closing session's connection. The matching opinfo, however,
stays linked in its per-ClientGuid lease_table_list entry's lb->lease_list
because destroy_lease_table() only runs on full TCP-connection teardown,
not on SESSION_LOGOFF.
If the same TCP connection then negotiates a fresh session with the
same ClientGuid (ClientGuid is bound to NEGOTIATE, not the session, and
is unchanged across LOGOFF + SETUP) and issues a SMB2 CREATE with a
lease context on a different inode, find_same_lease_key() walks
lb->lease_list, reaches the stale opinfo, and calls compare_guid_key(),
which unconditionally dereferences opinfo->conn->ClientGUID. The conn
pointer is NULL and the kernel panics.
Reproducer requires only a successful SMB2 SESSION_SETUP and a share
configured with 'durable handles = yes'. KASAN report on mainline
70390501d194:
general protection fault, probably for non-canonical address
0xdffffc0000000069: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000348-0x000000000000034f]
Workqueue: ksmbd-io handle_ksmbd_work
RIP: 0010:bcmp+0x5b/0x230
Call Trace:
compare_guid_key+0x4b/0xd0
find_same_lease_key+0x324/0x690
smb2_open+0x6aea/0x8e60
handle_ksmbd_work+0x796/0xee0
...
Faulting address 0x348 is the offset of ClientGUID within struct
ksmbd_conn, confirming opinfo->conn was NULL.
Read opinfo->conn once and bail out if it has been cleared by a
concurrent session_fd_check(). A half-detached opinfo cannot be the
owner of an active lease, so returning 0 is the correct match result. |
| In the Linux kernel, the following vulnerability has been resolved:
fbcon: fix NULL pointer dereference for a console without vc_data
fbcon_new_modelist() runs when a framebuffer's modelist changes. For each
console mapped to it with fb_display[i].mode set, it reads vc_cons[i].d and
passes the vc_num to fbcon_set_disp(). This assumes a console with a mode
set has a vc_data, but it can be NULL. fbcon_set_disp() sets
fb_display[i].mode before it checks vc_data, and fbcon_deinit() leaves the
mode set after the vc_data is freed. fbcon_new_modelist() then dereferences
the NULL vc_data.
Keep fb_display[i].mode set only while the console has a vc_data. Check
vc_data before setting the mode in fbcon_set_disp(), and clear the mode in
fbcon_deinit(). The existing mode check in fbcon_new_modelist() then skips
such consoles. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: mediatek: Fix possible nullptr KP in HWV cleanup/on-check
Should probe fail for HW_VOTER type power domains, this driver was
unconditionally trying to perform cleanup for DIRECT_CTL domains,
but only after checking if the target domain is powered on... with
the DIRECT_CTL scpsys_domain_is_on() code again.
And there's more: the scpsys_domain_is_on() function is also being
unconditionally used in the probe path, for any power domain that
has flag MTK_SCPD_KEEP_DEFAULT_OFF!
This bug was never experienced by anyone because the HWV domains
never failed probe, and because none of those is declared with the
aforementioned flag - but it's still something critical.
In order to fix this, add a check for MTCMOS Type and, based on
that, call the correct functions for an "is on" check, and also
do the same for the cleanup path, calling the correct functions
for the "power off" action.
For the latter, since there's a call to pm_genpd_remove() right
before calling power_off, be cautious and add a variation of the
power off functions (with a _internal suffix) for those to get a
pointer to scpsys_domain instead of one to generic_pm_domain as,
even if that's still working, this is way too much fragile and
would break at some point. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: reject user command submission without a command BO
amdxdna_drm_submit_execbuf() passes the user-supplied command BO handle
straight into amdxdna_cmd_submit() with drv_cmd == NULL. When the handle
is AMDXDNA_INVALID_BO_HANDLE (0), the block that fetches job->cmd_bo is
skipped, leaving it NULL, and no check rejects it on the user path (the
!job->cmd_bo guard lives inside the != INVALID branch).
The job is then armed and pushed to the DRM scheduler.
aie2_sched_job_run() takes the drv_cmd == NULL path and calls
amdxdna_cmd_set_state(job->cmd_bo) -> amdxdna_gem_vmap(NULL) ->
to_gobj(NULL)->dev, a NULL pointer dereference in the drm_sched worker.
A process with access to the accel node on a system with a probed AMD NPU
can trigger a kernel oops with a single AMDXDNA_EXEC_CMD ioctl
(cmd_handles = 0).
Only internal driver commands (SYNC_DEBUG_BO / ATTACH_DEBUG_BO)
legitimately pass AMDXDNA_INVALID_BO_HANDLE, and they always set drv_cmd.
Reject the invalid handle for user submissions (drv_cmd == NULL) at the
submit choke point so every user path is covered.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
dma-buf: dma-fence: Fix potential NULL pointer dereference
The commit mentioned in the fixes tag below introduced a mechanism
through which fence producers can fully decouple from fence consumers.
This, desirable, mechanism is based on the fence's signaled-bit as the
"decoupling point".
A sophisticated interaction between RCU and atomic instructions attempts
to ensure that fence consumers can still interact with fence producers
through the dma_fence_ops (callback pointers into the producer).
This is the desired behavior: to check for decoupling, the signaled-bit
is first checked. If it's not yet signaled, RCU ensures that the ops
pointer cannot yet be NULL.
Hereby, dma_fence_signal_timestamp_locked() first sets the signaled-bit,
and then sets the ops pointer to NULL. Readers first load the ops
pointer, and then check through the signaled-bit whether the pointer can
legally be accessed.
These set and load operations could occur out of order on weakly ordered
platforms. This problem can be solved very elegantly by using the ops
pointer itself as the synchronization point. The pointer is either NULL,
or cannot become NULL while it is being used thanks to RCU.
Replace the signaled-bit check in dma_fence_timeline_name() and
dma_fence_driver_name(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_multiq: Replace direct dequeue call with peek and qdisc_dequeue_peeked
multiq_dequeue() takes a packet from a band's child with a direct
->dequeue() call after multiq_peek() peeked it. When the child is
non-work-conserving the peek stashes the skb in the child's gso_skb, so
the direct dequeue returns a different skb and orphans the stash,
desyncing the child's qlen/backlog. With a qfq child reached through a
peeking parent (e.g. tbf) this re-enters the child on an emptied list and
dereferences NULL, panicking the kernel from softirq on ordinary egress.
Take the packet through qdisc_dequeue_peeked(), as sch_prio already does
and as sch_red and sch_sfb were just fixed to do. The helper is a no-op
when the child has no stash, so a work-conserving child is unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: TC, skip peer flow cleanup when LAG seq is unavailable
mlx5_lag_get_dev_seq() will return error when the peer isn't in the LAG
or when no device is marked as master. Result bad memory access and kernel
crash[1].
Hence, skip the peer when lookup fails.
Note: In case there are peer flows, they are cleaned before LAG cleared
the master mark.
[1]
RIP: 0010:mlx5e_tc_del_fdb_peers_flow+0x3d/0x350 [mlx5_core]
Call Trace:
<TASK>
mlx5e_tc_clean_fdb_peer_flows+0xc1/0x130 [mlx5_core]
mlx5_esw_offloads_unpair+0x3a/0x400 [mlx5_core]
mlx5_esw_offloads_devcom_event+0xee/0x360 [mlx5_core]
mlx5_devcom_send_event+0x7a/0x140 [mlx5_core]
mlx5_esw_offloads_devcom_cleanup+0x2f/0x90 [mlx5_core]
mlx5e_tc_esw_cleanup+0x28/0xf0 [mlx5_core]
mlx5e_rep_tc_cleanup+0x19/0x30 [mlx5_core]
mlx5e_cleanup_uplink_rep_tx+0x36/0x40 [mlx5_core]
mlx5e_cleanup_rep_tx+0x55/0x60 [mlx5_core]
mlx5e_detach_netdev+0x96/0xf0 [mlx5_core]
mlx5e_netdev_change_profile+0x5b/0x120 [mlx5_core]
mlx5e_netdev_attach_nic_profile+0x1b/0x30 [mlx5_core]
mlx5e_vport_rep_unload+0xdd/0x110 [mlx5_core]
__esw_offloads_unload_rep+0x81/0xb0 [mlx5_core]
mlx5_eswitch_unregister_vport_reps+0x1d7/0x220 [mlx5_core]
mlx5e_rep_remove+0x22/0x30 [mlx5_core]
device_release_driver_internal+0x194/0x1f0
bus_remove_device+0xe8/0x1b0
device_del+0x159/0x3c0
mlx5_rescan_drivers_locked+0xbc/0x2d0 [mlx5_core]
mlx5_unregister_device+0x54/0x80 [mlx5_core]
mlx5_uninit_one+0x73/0x130 [mlx5_core]
remove_one+0x78/0xe0 [mlx5_core]
pci_device_remove+0x39/0xa0 |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix missing NULL pointer check in afs_break_some_callbacks()
Fix afs_break_some_callbacks() to check to see if afs_lookup_volume_rcu()
returned NULL (e.g. the specified volume is unknown). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_fib: reject fib expression on the netdev egress hook
A fib expression in a netdev egress base chain dereferences nft_in(pkt),
NULL on the transmit path, causing a NULL pointer dereference at eval.
nft_fib_validate() masks the hook with NF_INET_* values, but netdev hook
numbers are a separate enum that aliases them (NF_NETDEV_EGRESS ==
NF_INET_LOCAL_IN), so an egress chain passes validation and then faults.
Add nft_fib_netdev_validate() that limits each result/flag to the netdev
hook where the device it reads exists: the input-device cases (OIF,
OIFNAME, ADDRTYPE with F_IIF) to ingress, the output-device case (ADDRTYPE
with F_OIF) to egress, ADDRTYPE with no device flag to both. Also restrict
nft_fib_validate() to NFPROTO_IPV4/IPV6/INET so its NF_INET_* masks are
not applied to another family's hooks. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: check label build before no_new_privs test
aa_change_profile() builds a replacement label with
fn_label_build_in_scope() before the no_new_privs subset check. The build
helper can fail and return NULL or an ERR_PTR, but the result was passed
to aa_label_is_unconfined_subset() before the existing IS_ERR_OR_NULL()
check.
Reuse the existing target-label build failure handling immediately after
the build. This preserves the current audit handling while preventing the
subset helper from dereferencing an invalid label. |
