Export limit exceeded: 25283 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (25283 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-46148 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for active-high devices or devices that need to transmit with the chip select disabled. Modify the driver so that it controls chip select directly, retaining the behaviour for mem_ops of setting the chip select active for the entire duration of the transfer in the exec_op callback. For regular transfers, implement the set_cs callback for the core to use. As part of this, the existing setup callback, mchp_coreqspi_setup_op(), is removed. Modifying the CLKIDLE field is not safe to do during operation when there are multiple devices, so this code is removed entirely. Setting the MASTER and ENABLE fields is something that can be done once at probe, it doesn't need to be re-run for each device. Instead the new setup callback sets the built-in chip select to its inactive state for active-low devices, as the reset value of the chip select in software controlled mode is low. | ||||
| CVE-2026-46147 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Fix pin leak and publication ordering in __pkvm_init_vcpu() Two bugs exist in the vCPU initialisation path: 1. If a check fails after hyp_pin_shared_mem() succeeds, the cleanup path jumps to 'unlock' without calling unpin_host_vcpu() or unpin_host_sve_state(), permanently leaking pin references on the host vCPU and SVE state pages. Extract a register_hyp_vcpu() helper that performs the checks and the store. When register_hyp_vcpu() returns an error, call unpin_host_vcpu() and unpin_host_sve_state() inline before falling through to the existing 'unlock' label. 2. register_hyp_vcpu() publishes the new vCPU pointer into 'hyp_vm->vcpus[]' with a bare store, allowing a concurrent caller of pkvm_load_hyp_vcpu() to observe a partially initialised vCPU object. Ensure the store uses smp_store_release() and the load uses smp_load_acquire(). While 'vm_table_lock' currently serialises the store and the load, these barriers ensure the reader sees the fully initialised 'hyp_vcpu' object even if there were a lockless path or if the lock's own ordering guarantees were insufficient for nested object initialization. | ||||
| CVE-2026-46144 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/mana: Fix error unwind in mana_ib_create_qp_rss() Sashiko points out that mana_ib_cfg_vport_steering() is leaked, the normal destroy path cleans it up. | ||||
| CVE-2026-11653 | 4 Apple, Google, Linux and 1 more | 4 Macos, Chrome, Linux Kernel and 1 more | 2026-06-10 | 6.5 Medium |
| Inappropriate implementation in Extensions in Google Chrome prior to 149.0.7827.103 allowed a remote attacker who had compromised the renderer process to bypass site isolation via a crafted HTML page. (Chromium security severity: High) | ||||
| CVE-2026-46176 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix error path fall-through in mlx5_ib_dev_res_srq_init() mlx5_ib_dev_res_srq_init() allocates two SRQs, s0 and s1. When ib_create_srq() fails for s1, the error branch destroys s0 but falls through and unconditionally assigns the freed s0 and the ERR_PTR s1 to devr->s0 and devr->s1. This leads to several problems: the lock-free fast path checks "if (devr->s1) return 0;" and treats the ERR_PTR as already initialised; users in mlx5_ib_create_qp() dereference the freed SRQ or ERR_PTR via to_msrq(devr->s0)->msrq.srqn; and mlx5_ib_dev_res_cleanup() dereferences the ERR_PTR and double-frees s0 on teardown. Fix by adding the same `goto unlock` in the s1 failure path. | ||||
| CVE-2026-46175 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: f2fs: fix fsck inconsistency caused by FGGC of node block During FGGC node block migration, fsck may incorrectly treat the migrated node block as fsync-written data. The reproduction scenario: root@vm:/mnt/f2fs# seq 1 2048 | xargs -n 1 ./test_sync // write inline inode and sync root@vm:/mnt/f2fs# rm -f 1 root@vm:/mnt/f2fs# sync root@vm:/mnt/f2fs# f2fs_io gc_range // move data block in sync mode and not write CP SPO, "fsck --dry-run" find inode has already checkpointed but still with DENT_BIT_SHIFT set The root cause is that GC does not clear the dentry mark and fsync mark during node block migration, leading fsck to misinterpret them as user-issued fsync writes. In BGGC mode, node block migration is handled by f2fs_sync_node_pages(), which guarantees the dentry and fsync marks are cleared before writing. This patch move the set/clear of the fsync|dentry marks into __write_node_folio to make the logic clearer, and ensures the fsync|dentry mark is cleared in FGGC. | ||||
| CVE-2026-46162 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ice: fix double free in ice_sf_eth_activate() error path When auxiliary_device_add() fails, ice_sf_eth_activate() jumps to aux_dev_uninit and calls auxiliary_device_uninit(&sf_dev->adev). The device release callback ice_sf_dev_release() frees sf_dev, but the current error path falls through to sf_dev_free and calls kfree(sf_dev) again, causing a double free. Keep kfree(sf_dev) for the auxiliary_device_init() failure path, but avoid falling through to sf_dev_free after auxiliary_device_uninit(). | ||||
| CVE-2026-46228 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: spi: ch341: fix devres lifetime USB drivers bind to USB interfaces and any device managed resources should have their lifetime tied to the interface rather than parent USB device. This avoids issues like memory leaks when drivers are unbound without their devices being physically disconnected (e.g. on probe deferral or configuration changes). Fix the controller and driver data lifetime so that they are released on driver unbind. Note that this also makes sure that the SPI controller is placed correctly under the USB interface in the device tree. | ||||
| CVE-2026-46229 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Clear VRAM on allocation to prevent stale data exposure KFD VRAM allocations set AMDGPU_GEM_CREATE_VRAM_WIPE_ON_RELEASE but not AMDGPU_GEM_CREATE_VRAM_CLEARED, leaving freshly allocated VRAM with stale data from prior use observable by compute kernels. The GEM ioctl path already sets VRAM_CLEARED for all userspace allocations via amdgpu_gem_create_ioctl() and amdgpu_mode_dumb_create(). The KFD path was missing this flag, allowing stale page table remnants to leak into user buffers. This causes crashes in RCCL P2P transport where non-zero data in ptrExchange/head/tail fields corrupts the protocol handshake. | ||||
| CVE-2026-46231 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: batman-adv: bla: put backbone reference on failed claim hash insert When batadv_bla_add_claim() fails to insert a new claim into the hash, it leaked a reference to the backbone_gw for which the claim was intended. Call batadv_backbone_gw_put() on the error path to release the reference and avoid leaking the backbone_gw object. | ||||
| CVE-2026-46232 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 8.1 High |
| In the Linux kernel, the following vulnerability has been resolved: HID: playstation: Clamp num_touch_reports A device would never lie about the number of touch reports would it? If it does the loop in dualshock4_parse_report will read off the end of the touch_reports array, up to about 2 KiB for the maximum number of 256 loop iteraions. The data that is read is emitted via evdev if the DS4_TOUCH_POINT_INACTIVE bit happens to be set. Protect against this by clamping the num_touch_reports value provided by the device to the maximum size of the touch_reports array. | ||||
| CVE-2026-46233 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: batman-adv: bla: only purge non-released claims When batadv_bla_purge_claims() goes through the list of claims, it is only traversing the hash list with an rcu_read_lock(). Due to a potential parallel batadv_claim_put(), it can happen that it encounters a claim which was actually in the process of being released+freed by batadv_claim_release(). In this case, backbone_gw is set to NULL before the delayed RCU kfree is started. Calling batadv_bla_claim_get_backbone_gw() is then no longer allowed because it would cause a NULL-ptr derefence. To avoid this, only claims with a valid reference counter must be purged. All others are already taken care of. | ||||
| CVE-2026-46235 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: media: saa7164: add ioremap return checks and cleanups Add checks for ioremap return values in saa7164_dev_setup(). If ioremap for BAR0 or BAR2 fails, release the already allocated PCI memory regions, remove the device from the global list, decrement the device count, and return -ENODEV. This prevents potential null pointer dereferences and ensures proper cleanup on memory mapping failures. | ||||
| CVE-2026-46236 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: media: rc: xbox_remote: heed DMA restrictions The buffer for IO must not be part of the device structure because that violates the DMA coherency rules. | ||||
| CVE-2026-46238 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 8.8 High |
| In the Linux kernel, the following vulnerability has been resolved: batman-adv: stop caching unowned originator pointers in BAT IV BAT IV keeps the last-hop neighbor address in each neigh_node, but some paths also cache an originator pointer derived from a temporary lookup. That pointer is not owned by the neigh_node and may no longer refer to a live originator entry after purge handling runs. Stop storing the auxiliary originator pointer in the BAT IV neighbor state. When BAT IV needs the neighbor originator data, resolve it from the stored neighbor address and drop the reference again after use. [sven: avoid bonding logic for outgoing OGM] | ||||
| CVE-2026-46239 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: media: i2c: ov5647: Fix runtime PM refcount leak in s_ctrl Three control cases (AUTOGAIN, EXPOSURE_AUTO, ANALOGUE_GAIN) directly return without calling pm_runtime_put(), causing runtime PM reference count leaks. Change these cases from 'return' to 'ret = ... break' pattern to ensure pm_runtime_put() is always called before function exit. | ||||
| CVE-2026-46240 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: media: iris: Fix use-after-free in iris_release_internal_buffers() The recent change in commit 1dabf00ee206 ("media: iris: gen1: Destroy internal buffers after FW releases") introduced a regression where session_release_buf() may free the buffer. The caller, iris_release_internal_buffers(), continued to access `buffer` after the call, leading to a potential use-after-free. Fix this by setting BUF_ATTR_PENDING_RELEASE before calling session_release_buf(), and reverting the flag if the call fails. This ensures no dereference occurs after potential freeing. | ||||
| CVE-2026-46241 | 1 Linux | 1 Linux Kernel | 2026-06-10 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: spi: mpc52xx: fix use-after-free on registration failure Make sure to disable and free the interrupts in case controller registration fails to avoid a potential use-after-free and resource leak. This issue was flagged by Sashiko when reviewing a controller deregistration fix. | ||||
| CVE-2026-4447 | 4 Apple, Google, Linux and 1 more | 4 Macos, Chrome, Linux Kernel and 1 more | 2026-06-10 | 8.8 High |
| Inappropriate implementation in V8 in Google Chrome prior to 146.0.7680.153 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: High) | ||||
| CVE-2026-11666 | 4 Apple, Google, Linux and 1 more | 4 Macos, Chrome, Linux Kernel and 1 more | 2026-06-10 | 5.4 Medium |
| Insufficient validation of untrusted input in Input in Google Chrome prior to 149.0.7827.103 allowed a remote attacker to perform UI spoofing via a crafted HTML page. (Chromium security severity: High) | ||||