| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
pidfs: validate extensible ioctls
Validate extensible ioctls stricter than we do now. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: prevent poison consumption when splitting THP
When performing memory error injection on a THP (Transparent Huge Page)
mapped to userspace on an x86 server, the kernel panics with the following
trace. The expected behavior is to terminate the affected process instead
of panicking the kernel, as the x86 Machine Check code can recover from an
in-userspace #MC.
mce: [Hardware Error]: CPU 0: Machine Check Exception: f Bank 3: bd80000000070134
mce: [Hardware Error]: RIP 10:<ffffffff8372f8bc> {memchr_inv+0x4c/0xf0}
mce: [Hardware Error]: TSC afff7bbff88a ADDR 1d301b000 MISC 80 PPIN 1e741e77539027db
mce: [Hardware Error]: PROCESSOR 0:d06d0 TIME 1758093249 SOCKET 0 APIC 0 microcode 80000320
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
mce: [Hardware Error]: Machine check: Data load in unrecoverable area of kernel
Kernel panic - not syncing: Fatal local machine check
The root cause of this panic is that handling a memory failure triggered
by an in-userspace #MC necessitates splitting the THP. The splitting
process employs a mechanism, implemented in
try_to_map_unused_to_zeropage(), which reads the pages in the THP to
identify zero-filled pages. However, reading the pages in the THP results
in a second in-kernel #MC, occurring before the initial memory_failure()
completes, ultimately leading to a kernel panic. See the kernel panic
call trace on the two #MCs.
First Machine Check occurs // [1]
memory_failure() // [2]
try_to_split_thp_page()
split_huge_page()
split_huge_page_to_list_to_order()
__folio_split() // [3]
remap_page()
remove_migration_ptes()
remove_migration_pte()
try_to_map_unused_to_zeropage() // [4]
memchr_inv() // [5]
Second Machine Check occurs // [6]
Kernel panic
[1] Triggered by accessing a hardware-poisoned THP in userspace, which is
typically recoverable by terminating the affected process.
[2] Call folio_set_has_hwpoisoned() before try_to_split_thp_page().
[3] Pass the RMP_USE_SHARED_ZEROPAGE remap flag to remap_page().
[4] Try to map the unused THP to zeropage.
[5] Re-access pages in the hw-poisoned THP in the kernel.
[6] Triggered in-kernel, leading to a panic kernel.
In Step[2], memory_failure() sets the poisoned flag on the page in the THP
by TestSetPageHWPoison() before calling try_to_split_thp_page().
As suggested by David Hildenbrand, fix this panic by not accessing to the
poisoned page in the THP during zeropage identification, while continuing
to scan unaffected pages in the THP for possible zeropage mapping. This
prevents a second in-kernel #MC that would cause kernel panic in Step[4].
Thanks to Andrew Zaborowski for his initial work on fixing this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
rv: Fully convert enabled_monitors to use list_head as iterator
The callbacks in enabled_monitors_seq_ops are inconsistent. Some treat the
iterator as struct rv_monitor *, while others treat the iterator as struct
list_head *.
This causes a wrong type cast and crashes the system as reported by Nathan.
Convert everything to use struct list_head * as iterator. This also makes
enabled_monitors consistent with available_monitors. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/meson: explicitly remove aggregate driver at module unload time
Because component_master_del wasn't being called when unloading the
meson_drm module, the aggregate device would linger forever in the global
aggregate_devices list. That means when unloading and reloading the
meson_dw_hdmi module, component_add would call into
try_to_bring_up_aggregate_device and find the unbound meson_drm aggregate
device.
This would in turn dereference some of the aggregate_device's struct
entries which point to memory automatically freed by the devres API when
unbinding the aggregate device from meson_drv_unbind, and trigger an
use-after-free bug:
[ +0.000014] =============================================================
[ +0.000007] BUG: KASAN: use-after-free in find_components+0x468/0x500
[ +0.000017] Read of size 8 at addr ffff000006731688 by task modprobe/2536
[ +0.000018] CPU: 4 PID: 2536 Comm: modprobe Tainted: G C O 5.19.0-rc6-lrmbkasan+ #1
[ +0.000010] Hardware name: Hardkernel ODROID-N2Plus (DT)
[ +0.000008] Call trace:
[ +0.000005] dump_backtrace+0x1ec/0x280
[ +0.000011] show_stack+0x24/0x80
[ +0.000007] dump_stack_lvl+0x98/0xd4
[ +0.000010] print_address_description.constprop.0+0x80/0x520
[ +0.000011] print_report+0x128/0x260
[ +0.000007] kasan_report+0xb8/0xfc
[ +0.000007] __asan_report_load8_noabort+0x3c/0x50
[ +0.000009] find_components+0x468/0x500
[ +0.000008] try_to_bring_up_aggregate_device+0x64/0x390
[ +0.000009] __component_add+0x1dc/0x49c
[ +0.000009] component_add+0x20/0x30
[ +0.000008] meson_dw_hdmi_probe+0x28/0x34 [meson_dw_hdmi]
[ +0.000013] platform_probe+0xd0/0x220
[ +0.000008] really_probe+0x3ac/0xa80
[ +0.000008] __driver_probe_device+0x1f8/0x400
[ +0.000008] driver_probe_device+0x68/0x1b0
[ +0.000008] __driver_attach+0x20c/0x480
[ +0.000009] bus_for_each_dev+0x114/0x1b0
[ +0.000007] driver_attach+0x48/0x64
[ +0.000009] bus_add_driver+0x390/0x564
[ +0.000007] driver_register+0x1a8/0x3e4
[ +0.000009] __platform_driver_register+0x6c/0x94
[ +0.000007] meson_dw_hdmi_platform_driver_init+0x30/0x1000 [meson_dw_hdmi]
[ +0.000014] do_one_initcall+0xc4/0x2b0
[ +0.000008] do_init_module+0x154/0x570
[ +0.000010] load_module+0x1a78/0x1ea4
[ +0.000008] __do_sys_init_module+0x184/0x1cc
[ +0.000008] __arm64_sys_init_module+0x78/0xb0
[ +0.000008] invoke_syscall+0x74/0x260
[ +0.000008] el0_svc_common.constprop.0+0xcc/0x260
[ +0.000009] do_el0_svc+0x50/0x70
[ +0.000008] el0_svc+0x68/0x1a0
[ +0.000009] el0t_64_sync_handler+0x11c/0x150
[ +0.000009] el0t_64_sync+0x18c/0x190
[ +0.000014] Allocated by task 902:
[ +0.000007] kasan_save_stack+0x2c/0x5c
[ +0.000009] __kasan_kmalloc+0x90/0xd0
[ +0.000007] __kmalloc_node+0x240/0x580
[ +0.000010] memcg_alloc_slab_cgroups+0xa4/0x1ac
[ +0.000010] memcg_slab_post_alloc_hook+0xbc/0x4c0
[ +0.000008] kmem_cache_alloc_node+0x1d0/0x490
[ +0.000009] __alloc_skb+0x1d4/0x310
[ +0.000010] alloc_skb_with_frags+0x8c/0x620
[ +0.000008] sock_alloc_send_pskb+0x5ac/0x6d0
[ +0.000010] unix_dgram_sendmsg+0x2e0/0x12f0
[ +0.000010] sock_sendmsg+0xcc/0x110
[ +0.000007] sock_write_iter+0x1d0/0x304
[ +0.000008] new_sync_write+0x364/0x460
[ +0.000007] vfs_write+0x420/0x5ac
[ +0.000008] ksys_write+0x19c/0x1f0
[ +0.000008] __arm64_sys_write+0x78/0xb0
[ +0.000007] invoke_syscall+0x74/0x260
[ +0.000008] el0_svc_common.constprop.0+0x1a8/0x260
[ +0.000009] do_el0_svc+0x50/0x70
[ +0.000007] el0_svc+0x68/0x1a0
[ +0.000008] el0t_64_sync_handler+0x11c/0x150
[ +0.000008] el0t_64_sync+0x18c/0x190
[ +0.000013] Freed by task 2509:
[ +0.000008] kasan_save_stack+0x2c/0x5c
[ +0.000007] kasan_set_track+0x2c/0x40
[ +0.000008] kasan_set_free_info+0x28/0x50
[ +0.000008] ____kasan_slab_free+0x128/0x1d4
[ +0.000008] __kasan_slab_free+0x18/0x24
[ +0.000007] slab_free_freelist_hook+0x108/0x230
[ +0.000010]
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix bug_on in __es_tree_search caused by bad boot loader inode
We got a issue as fllows:
==================================================================
kernel BUG at fs/ext4/extents_status.c:203!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 945 Comm: cat Not tainted 6.0.0-next-20221007-dirty #349
RIP: 0010:ext4_es_end.isra.0+0x34/0x42
RSP: 0018:ffffc9000143b768 EFLAGS: 00010203
RAX: 0000000000000000 RBX: ffff8881769cd0b8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8fc27cf7 RDI: 00000000ffffffff
RBP: ffff8881769cd0bc R08: 0000000000000000 R09: ffffc9000143b5f8
R10: 0000000000000001 R11: 0000000000000001 R12: ffff8881769cd0a0
R13: ffff8881768e5668 R14: 00000000768e52f0 R15: 0000000000000000
FS: 00007f359f7f05c0(0000)GS:ffff88842fd00000(0000)knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f359f5a2000 CR3: 000000017130c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__es_tree_search.isra.0+0x6d/0xf5
ext4_es_cache_extent+0xfa/0x230
ext4_cache_extents+0xd2/0x110
ext4_find_extent+0x5d5/0x8c0
ext4_ext_map_blocks+0x9c/0x1d30
ext4_map_blocks+0x431/0xa50
ext4_mpage_readpages+0x48e/0xe40
ext4_readahead+0x47/0x50
read_pages+0x82/0x530
page_cache_ra_unbounded+0x199/0x2a0
do_page_cache_ra+0x47/0x70
page_cache_ra_order+0x242/0x400
ondemand_readahead+0x1e8/0x4b0
page_cache_sync_ra+0xf4/0x110
filemap_get_pages+0x131/0xb20
filemap_read+0xda/0x4b0
generic_file_read_iter+0x13a/0x250
ext4_file_read_iter+0x59/0x1d0
vfs_read+0x28f/0x460
ksys_read+0x73/0x160
__x64_sys_read+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
==================================================================
In the above issue, ioctl invokes the swap_inode_boot_loader function to
swap inode<5> and inode<12>. However, inode<5> contain incorrect imode and
disordered extents, and i_nlink is set to 1. The extents check for inode in
the ext4_iget function can be bypassed bacause 5 is EXT4_BOOT_LOADER_INO.
While links_count is set to 1, the extents are not initialized in
swap_inode_boot_loader. After the ioctl command is executed successfully,
the extents are swapped to inode<12>, in this case, run the `cat` command
to view inode<12>. And Bug_ON is triggered due to the incorrect extents.
When the boot loader inode is not initialized, its imode can be one of the
following:
1) the imode is a bad type, which is marked as bad_inode in ext4_iget and
set to S_IFREG.
2) the imode is good type but not S_IFREG.
3) the imode is S_IFREG.
The BUG_ON may be triggered by bypassing the check in cases 1 and 2.
Therefore, when the boot loader inode is bad_inode or its imode is not
S_IFREG, initialize the inode to avoid triggering the BUG. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
I found a null pointer reference in arch_prepare_kprobe():
# echo 'p cmdline_proc_show' > kprobe_events
# echo 'p cmdline_proc_show+16' >> kprobe_events
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000050bfc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 122 Comm: sh Not tainted 6.0.0-rc3-00007-gdcf8e5633e2e #10
NIP: c000000000050bfc LR: c000000000050bec CTR: 0000000000005bdc
REGS: c0000000348475b0 TRAP: 0300 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 88002444 XER: 20040006
CFAR: c00000000022d100 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 0
...
NIP arch_prepare_kprobe+0x10c/0x2d0
LR arch_prepare_kprobe+0xfc/0x2d0
Call Trace:
0xc0000000012f77a0 (unreliable)
register_kprobe+0x3c0/0x7a0
__register_trace_kprobe+0x140/0x1a0
__trace_kprobe_create+0x794/0x1040
trace_probe_create+0xc4/0xe0
create_or_delete_trace_kprobe+0x2c/0x80
trace_parse_run_command+0xf0/0x210
probes_write+0x20/0x40
vfs_write+0xfc/0x450
ksys_write+0x84/0x140
system_call_exception+0x17c/0x3a0
system_call_vectored_common+0xe8/0x278
--- interrupt: 3000 at 0x7fffa5682de0
NIP: 00007fffa5682de0 LR: 0000000000000000 CTR: 0000000000000000
REGS: c000000034847e80 TRAP: 3000 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 900000000280f033 <SF,HV,VEC,VSX,EE,PR,FP,ME,IR,DR,RI,LE> CR: 44002408 XER: 00000000
The address being probed has some special:
cmdline_proc_show: Probe based on ftrace
cmdline_proc_show+16: Probe for the next instruction at the ftrace location
The ftrace-based kprobe does not generate kprobe::ainsn::insn, it gets
set to NULL. In arch_prepare_kprobe() it will check for:
...
prev = get_kprobe(p->addr - 1);
preempt_enable_no_resched();
if (prev && ppc_inst_prefixed(ppc_inst_read(prev->ainsn.insn))) {
...
If prev is based on ftrace, 'ppc_inst_read(prev->ainsn.insn)' will occur
with a null pointer reference. At this point prev->addr will not be a
prefixed instruction, so the check can be skipped.
Check if prev is ftrace-based kprobe before reading 'prev->ainsn.insn'
to fix this problem.
[mpe: Trim oops] |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: mte: Avoid setting PG_mte_tagged if no tags cleared or restored
Prior to commit 69e3b846d8a7 ("arm64: mte: Sync tags for pages where PTE
is untagged"), mte_sync_tags() was only called for pte_tagged() entries
(those mapped with PROT_MTE). Therefore mte_sync_tags() could safely use
test_and_set_bit(PG_mte_tagged, &page->flags) without inadvertently
setting PG_mte_tagged on an untagged page.
The above commit was required as guests may enable MTE without any
control at the stage 2 mapping, nor a PROT_MTE mapping in the VMM.
However, the side-effect was that any page with a PTE that looked like
swap (or migration) was getting PG_mte_tagged set automatically. A
subsequent page copy (e.g. migration) copied the tags to the destination
page even if the tags were owned by KASAN.
This issue was masked by the page_kasan_tag_reset() call introduced in
commit e5b8d9218951 ("arm64: mte: reset the page tag in page->flags").
When this commit was reverted (20794545c146), KASAN started reporting
access faults because the overriding tags in a page did not match the
original page->flags (with CONFIG_KASAN_HW_TAGS=y):
BUG: KASAN: invalid-access in copy_page+0x10/0xd0 arch/arm64/lib/copy_page.S:26
Read at addr f5ff000017f2e000 by task syz-executor.1/2218
Pointer tag: [f5], memory tag: [f2]
Move the PG_mte_tagged bit setting from mte_sync_tags() to the actual
place where tags are cleared (mte_sync_page_tags()) or restored
(mte_restore_tags()). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
I got a null-ptr-defer error report when I do the following tests
on the qemu platform:
make defconfig and CONFIG_PARPORT=m, CONFIG_PARPORT_PC=m,
CONFIG_SND_MTS64=m
Then making test scripts:
cat>test_mod1.sh<<EOF
modprobe snd-mts64
modprobe snd-mts64
EOF
Executing the script, perhaps several times, we will get a null-ptr-defer
report, as follow:
syzkaller:~# ./test_mod.sh
snd_mts64: probe of snd_mts64.0 failed with error -5
modprobe: ERROR: could not insert 'snd_mts64': No such device
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 0 PID: 205 Comm: modprobe Not tainted 6.1.0-rc8-00588-g76dcd734eca2 #6
Call Trace:
<IRQ>
snd_mts64_interrupt+0x24/0xa0 [snd_mts64]
parport_irq_handler+0x37/0x50 [parport]
__handle_irq_event_percpu+0x39/0x190
handle_irq_event_percpu+0xa/0x30
handle_irq_event+0x2f/0x50
handle_edge_irq+0x99/0x1b0
__common_interrupt+0x5d/0x100
common_interrupt+0xa0/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:_raw_write_unlock_irqrestore+0x11/0x30
parport_claim+0xbd/0x230 [parport]
snd_mts64_probe+0x14a/0x465 [snd_mts64]
platform_probe+0x3f/0xa0
really_probe+0x129/0x2c0
__driver_probe_device+0x6d/0xc0
driver_probe_device+0x1a/0xa0
__device_attach_driver+0x7a/0xb0
bus_for_each_drv+0x62/0xb0
__device_attach+0xe4/0x180
bus_probe_device+0x82/0xa0
device_add+0x550/0x920
platform_device_add+0x106/0x220
snd_mts64_attach+0x2e/0x80 [snd_mts64]
port_check+0x14/0x20 [parport]
bus_for_each_dev+0x6e/0xc0
__parport_register_driver+0x7c/0xb0 [parport]
snd_mts64_module_init+0x31/0x1000 [snd_mts64]
do_one_initcall+0x3c/0x1f0
do_init_module+0x46/0x1c6
load_module+0x1d8d/0x1e10
__do_sys_finit_module+0xa2/0xf0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..
The mts wa not initialized during interrupt, we add check for
mts to fix this bug. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: stratix10-svc: fix bug in saving controller data
Fix the incorrect usage of platform_set_drvdata and dev_set_drvdata. They
both are of the same data and overrides each other. This resulted in the
rmmod of the svc driver to fail and throw a kernel panic for kthread_stop
and fifo free. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa_sim: fix possible memory leak in vdpasim_net_init() and vdpasim_blk_init()
Inject fault while probing module, if device_register() fails in
vdpasim_net_init() or vdpasim_blk_init(), but the refcount of kobject is
not decreased to 0, the name allocated in dev_set_name() is leaked.
Fix this by calling put_device(), so that name can be freed in
callback function kobject_cleanup().
(vdpa_sim_net)
unreferenced object 0xffff88807eebc370 (size 16):
comm "modprobe", pid 3848, jiffies 4362982860 (age 18.153s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 6e 65 74 00 6b 6b 6b a5 vdpasim_net.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0270013>] 0xffffffffa0270013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
(vdpa_sim_blk)
unreferenced object 0xffff8881070c1250 (size 16):
comm "modprobe", pid 6844, jiffies 4364069319 (age 17.572s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 62 6c 6b 00 6b 6b 6b a5 vdpasim_blk.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0220013>] 0xffffffffa0220013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: uas: fix urb unmapping issue when the uas device is remove during ongoing data transfer
When a UAS device is unplugged during data transfer, there is
a probability of a system panic occurring. The root cause is
an access to an invalid memory address during URB callback handling.
Specifically, this happens when the dma_direct_unmap_sg() function
is called within the usb_hcd_unmap_urb_for_dma() interface, but the
sg->dma_address field is 0 and the sg data structure has already been
freed.
The SCSI driver sends transfer commands by invoking uas_queuecommand_lck()
in uas.c, using the uas_submit_urbs() function to submit requests to USB.
Within the uas_submit_urbs() implementation, three URBs (sense_urb,
data_urb, and cmd_urb) are sequentially submitted. Device removal may
occur at any point during uas_submit_urbs execution, which may result
in URB submission failure. However, some URBs might have been successfully
submitted before the failure, and uas_submit_urbs will return the -ENODEV
error code in this case. The current error handling directly calls
scsi_done(). In the SCSI driver, this eventually triggers scsi_complete()
to invoke scsi_end_request() for releasing the sgtable. The successfully
submitted URBs, when being unlinked to giveback, call
usb_hcd_unmap_urb_for_dma() in hcd.c, leading to exceptions during sg
unmapping operations since the sg data structure has already been freed.
This patch modifies the error condition check in the uas_submit_urbs()
function. When a UAS device is removed but one or more URBs have already
been successfully submitted to USB, it avoids immediately invoking
scsi_done() and save the cmnd to devinfo->cmnd array. If the successfully
submitted URBs is completed before devinfo->resetting being set, then
the scsi_done() function will be called within uas_try_complete() after
all pending URB operations are finalized. Otherwise, the scsi_done()
function will be called within uas_zap_pending(), which is executed after
usb_kill_anchored_urbs().
The error handling only takes effect when uas_queuecommand_lck() calls
uas_submit_urbs() and returns the error value -ENODEV . In this case,
the device is disconnected, and the flow proceeds to uas_disconnect(),
where uas_zap_pending() is invoked to call uas_try_complete(). |
| In the Linux kernel, the following vulnerability has been resolved:
atm/fore200e: Fix possible data race in fore200e_open()
Protect access to fore200e->available_cell_rate with rate_mtx lock in the
error handling path of fore200e_open() to prevent a data race.
The field fore200e->available_cell_rate is a shared resource used to track
available bandwidth. It is concurrently accessed by fore200e_open(),
fore200e_close(), and fore200e_change_qos().
In fore200e_open(), the lock rate_mtx is correctly held when subtracting
vcc->qos.txtp.max_pcr from available_cell_rate to reserve bandwidth.
However, if the subsequent call to fore200e_activate_vcin() fails, the
function restores the reserved bandwidth by adding back to
available_cell_rate without holding the lock.
This introduces a race condition because available_cell_rate is a global
device resource shared across all VCCs. If the error path in
fore200e_open() executes concurrently with operations like
fore200e_close() or fore200e_change_qos() on other VCCs, a
read-modify-write race occurs.
Specifically, the error path reads the rate without the lock. If another
CPU acquires the lock and modifies the rate (e.g., releasing bandwidth in
fore200e_close()) between this read and the subsequent write, the error
path will overwrite the concurrent update with a stale value. This results
in incorrect bandwidth accounting. |
| In the Linux kernel, the following vulnerability has been resolved:
media: imx-jpeg: Disable useless interrupt to avoid kernel panic
There is a hardware bug that the interrupt STMBUF_HALF may be triggered
after or when disable interrupt.
It may led to unexpected kernel panic.
And interrupt STMBUF_HALF and STMBUF_RTND have no other effect.
So disable them and the unused interrupts.
meanwhile clear the interrupt status when disable interrupt. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: marvell/octeontx - prevent integer overflows
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "code_length * 2" can overflow. The round_up(ucode_size, 16) +
sizeof() expression can overflow too. Prevent these overflows. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix refcount leak in hns_roce_mmap
rdma_user_mmap_entry_get_pgoff() takes the reference.
Add missing rdma_user_mmap_entry_put() to release the reference.
Acked-by Haoyue Xu <xuhaoyue1@hisilicon.com> |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/DOE: Fix memory leak with CONFIG_DEBUG_OBJECTS=y
After a pci_doe_task completes, its work_struct needs to be destroyed
to avoid a memory leak with CONFIG_DEBUG_OBJECTS=y. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: Add !tpm_amd_is_rng_defective() to the hwrng_unregister() call site
The following crash was reported:
[ 1950.279393] list_del corruption, ffff99560d485790->next is NULL
[ 1950.279400] ------------[ cut here ]------------
[ 1950.279401] kernel BUG at lib/list_debug.c:49!
[ 1950.279405] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 1950.279407] CPU: 11 PID: 5886 Comm: modprobe Tainted: G O 6.2.8_1 #1
[ 1950.279409] Hardware name: Gigabyte Technology Co., Ltd. B550M AORUS PRO-P/B550M AORUS PRO-P,
BIOS F15c 05/11/2022
[ 1950.279410] RIP: 0010:__list_del_entry_valid+0x59/0xc0
[ 1950.279415] Code: 48 8b 01 48 39 f8 75 5a 48 8b 72 08 48 39 c6 75 65 b8 01 00 00 00 c3 cc cc cc
cc 48 89 fe 48 c7 c7 08 a8 13 9e e8 b7 0a bc ff <0f> 0b 48 89 fe 48 c7 c7 38 a8 13 9e e8 a6 0a bc
ff 0f 0b 48 89 fe
[ 1950.279416] RSP: 0018:ffffa96d05647e08 EFLAGS: 00010246
[ 1950.279418] RAX: 0000000000000033 RBX: ffff99560d485750 RCX: 0000000000000000
[ 1950.279419] RDX: 0000000000000000 RSI: ffffffff9e107c59 RDI: 00000000ffffffff
[ 1950.279420] RBP: ffffffffc19c5168 R08: 0000000000000000 R09: ffffa96d05647cc8
[ 1950.279421] R10: 0000000000000003 R11: ffffffff9ea2a568 R12: 0000000000000000
[ 1950.279422] R13: ffff99560140a2e0 R14: ffff99560127d2e0 R15: 0000000000000000
[ 1950.279422] FS: 00007f67da795380(0000) GS:ffff995d1f0c0000(0000) knlGS:0000000000000000
[ 1950.279424] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1950.279424] CR2: 00007f67da7e65c0 CR3: 00000001feed2000 CR4: 0000000000750ee0
[ 1950.279426] PKRU: 55555554
[ 1950.279426] Call Trace:
[ 1950.279428] <TASK>
[ 1950.279430] hwrng_unregister+0x28/0xe0 [rng_core]
[ 1950.279436] tpm_chip_unregister+0xd5/0xf0 [tpm]
Add the forgotten !tpm_amd_is_rng_defective() invariant to the
hwrng_unregister() call site inside tpm_chip_unregister(). |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_pmem: add the missing REQ_OP_WRITE for flush bio
When doing mkfs.xfs on a pmem device, the following warning was
------------[ cut here ]------------
WARNING: CPU: 2 PID: 384 at block/blk-core.c:751 submit_bio_noacct
Modules linked in:
CPU: 2 PID: 384 Comm: mkfs.xfs Not tainted 6.4.0-rc7+ #154
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:submit_bio_noacct+0x340/0x520
......
Call Trace:
<TASK>
? submit_bio_noacct+0xd5/0x520
submit_bio+0x37/0x60
async_pmem_flush+0x79/0xa0
nvdimm_flush+0x17/0x40
pmem_submit_bio+0x370/0x390
__submit_bio+0xbc/0x190
submit_bio_noacct_nocheck+0x14d/0x370
submit_bio_noacct+0x1ef/0x520
submit_bio+0x55/0x60
submit_bio_wait+0x5a/0xc0
blkdev_issue_flush+0x44/0x60
The root cause is that submit_bio_noacct() needs bio_op() is either
WRITE or ZONE_APPEND for flush bio and async_pmem_flush() doesn't assign
REQ_OP_WRITE when allocating flush bio, so submit_bio_noacct just fail
the flush bio.
Simply fix it by adding the missing REQ_OP_WRITE for flush bio. And we
could fix the flush order issue and do flush optimization later. |
| In the Linux kernel, the following vulnerability has been resolved:
inotify: Avoid reporting event with invalid wd
When inotify_freeing_mark() races with inotify_handle_inode_event() it
can happen that inotify_handle_inode_event() sees that i_mark->wd got
already reset to -1 and reports this value to userspace which can
confuse the inotify listener. Avoid the problem by validating that wd is
sensible (and pretend the mark got removed before the event got
generated otherwise). |
