In the Linux kernel, the following vulnerability has been resolved:
idpf: disable DIM work before freeing q_vectors
idpf never drains the Tx/Rx DIM works before freeing the memory they
live in. tx_dim and rx_dim are embedded in struct idpf_q_vector, they
are queued from the NAPI poll via net_dim(), and idpf_vport_intr_rel()
ends with kfree(rsrc->q_vectors). Nothing in the driver cancels them.
idpf_tx_dim_work() and idpf_rx_dim_work() then run on freed memory:
idpf_vport_intr_write_itr() writes the ITR register through
q_vector->intr_reg.tx_itr / rx_itr, void __iomem pointers loaded out of
the freed q_vector. No configuration is needed to get there --
IDPF_ITR_IS_DYNAMIC() is defined as (itr_mode) and idpf_vport_alloc()
initialises both modes to IDPF_ITR_DYNAMIC.
Draining after idpf_vport_intr_napi_dis_all() is not enough on its own.
idpf_net_dim() is called from inside the
"if (napi_complete_done(napi, work_done))" branch of the poll, and
napi_complete_done() has already cleared NAPIF_STATE_SCHED by then.
napi_disable_locked() waits only while (val & (NAPIF_STATE_SCHED |
NAPIF_STATE_NPSVC)), so napi_disable() can return while the poll tail is
still queueing the work, and a plain cancel_work_sync() would be
re-armed behind the drain.
Use disable_work_sync(): schedule_work() on a work with a non-zero
disable count is dropped by clear_pending_if_disabled() before
__queue_work() is reached.
Move idpf_init_dim() to idpf_vport_intr_alloc() so the works are
initialised on every path that can reach the drain -- the three
"goto intr_deinit" sites between idpf_vport_intr_init() and
idpf_vport_intr_ena() get there without the enable side having run.
Nothing re-enables them: rsrc->q_vectors is freed on every exit from
idpf_vport_open() and on every idpf_vport_stop(), so the count dies with
the object.
It is a race, not a deterministic failure -- net_dim() only schedules
once DIM_NEVENTS events have accumulated and the profile index changes.
A KASAN ifup/ifdown loop under load is the way to see it.
idpf: disable DIM work before freeing q_vectors
idpf never drains the Tx/Rx DIM works before freeing the memory they
live in. tx_dim and rx_dim are embedded in struct idpf_q_vector, they
are queued from the NAPI poll via net_dim(), and idpf_vport_intr_rel()
ends with kfree(rsrc->q_vectors). Nothing in the driver cancels them.
idpf_tx_dim_work() and idpf_rx_dim_work() then run on freed memory:
idpf_vport_intr_write_itr() writes the ITR register through
q_vector->intr_reg.tx_itr / rx_itr, void __iomem pointers loaded out of
the freed q_vector. No configuration is needed to get there --
IDPF_ITR_IS_DYNAMIC() is defined as (itr_mode) and idpf_vport_alloc()
initialises both modes to IDPF_ITR_DYNAMIC.
Draining after idpf_vport_intr_napi_dis_all() is not enough on its own.
idpf_net_dim() is called from inside the
"if (napi_complete_done(napi, work_done))" branch of the poll, and
napi_complete_done() has already cleared NAPIF_STATE_SCHED by then.
napi_disable_locked() waits only while (val & (NAPIF_STATE_SCHED |
NAPIF_STATE_NPSVC)), so napi_disable() can return while the poll tail is
still queueing the work, and a plain cancel_work_sync() would be
re-armed behind the drain.
Use disable_work_sync(): schedule_work() on a work with a non-zero
disable count is dropped by clear_pending_if_disabled() before
__queue_work() is reached.
Move idpf_init_dim() to idpf_vport_intr_alloc() so the works are
initialised on every path that can reach the drain -- the three
"goto intr_deinit" sites between idpf_vport_intr_init() and
idpf_vport_intr_ena() get there without the enable side having run.
Nothing re-enables them: rsrc->q_vectors is freed on every exit from
idpf_vport_open() and on every idpf_vport_stop(), so the count dies with
the object.
It is a race, not a deterministic failure -- net_dim() only schedules
once DIM_NEVENTS events have accumulated and the profile index changes.
A KASAN ifup/ifdown loop under load is the way to see it.
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Fri, 25 Sep 2026 10:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: idpf: disable DIM work before freeing q_vectors idpf never drains the Tx/Rx DIM works before freeing the memory they live in. tx_dim and rx_dim are embedded in struct idpf_q_vector, they are queued from the NAPI poll via net_dim(), and idpf_vport_intr_rel() ends with kfree(rsrc->q_vectors). Nothing in the driver cancels them. idpf_tx_dim_work() and idpf_rx_dim_work() then run on freed memory: idpf_vport_intr_write_itr() writes the ITR register through q_vector->intr_reg.tx_itr / rx_itr, void __iomem pointers loaded out of the freed q_vector. No configuration is needed to get there -- IDPF_ITR_IS_DYNAMIC() is defined as (itr_mode) and idpf_vport_alloc() initialises both modes to IDPF_ITR_DYNAMIC. Draining after idpf_vport_intr_napi_dis_all() is not enough on its own. idpf_net_dim() is called from inside the "if (napi_complete_done(napi, work_done))" branch of the poll, and napi_complete_done() has already cleared NAPIF_STATE_SCHED by then. napi_disable_locked() waits only while (val & (NAPIF_STATE_SCHED | NAPIF_STATE_NPSVC)), so napi_disable() can return while the poll tail is still queueing the work, and a plain cancel_work_sync() would be re-armed behind the drain. Use disable_work_sync(): schedule_work() on a work with a non-zero disable count is dropped by clear_pending_if_disabled() before __queue_work() is reached. Move idpf_init_dim() to idpf_vport_intr_alloc() so the works are initialised on every path that can reach the drain -- the three "goto intr_deinit" sites between idpf_vport_intr_init() and idpf_vport_intr_ena() get there without the enable side having run. Nothing re-enables them: rsrc->q_vectors is freed on every exit from idpf_vport_open() and on every idpf_vport_stop(), so the count dies with the object. It is a race, not a deterministic failure -- net_dim() only schedules once DIM_NEVENTS events have accumulated and the profile index changes. A KASAN ifup/ifdown loop under load is the way to see it. | |
| Title | idpf: disable DIM work before freeing q_vectors | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2026-09-25T10:22:16.015Z
Reserved: 2026-09-24T16:01:01.158Z
Link: CVE-2026-97603
Vulnrichment
No data.
NVD
Status : Received
Published: 2026-09-25T11:17:13.393
Modified: 2026-09-25T11:17:13.393
Link: CVE-2026-97603
Redhat
No data.
OpenCVE Enrichment
No data.
Weaknesses
No weakness.