In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_qca: Do not write to the serial port after it is closed
hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP
is set (for example, for the WCN399x family). A failed hci_dev_open_sync()
following a successful qca_setup() calls hdev->close() but not
hdev->shutdown(), so the port is closed while power->vregs_on is left true.
qca_serdev_remove() then passes its power->vregs_on test and calls
qca_power_off(), which writes to the closed port unconditionally.
Seen on a WCN3988 by unbinding the driver after a controller failure. The
trace below is from a 7.0.0 based kernel, where qca_power_off() was still
named qca_power_shutdown():
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000038
Call trace:
tty_set_termios+0x50/0x238 (P)
ttyport_set_baudrate+0x84/0xc0
serdev_device_set_baudrate+0x24/0x40
qca_power_shutdown+0x158/0x1fc [hci_uart]
qca_serdev_remove+0x54/0x68 [hci_uart]
serdev_drv_remove+0x1c/0x2c
device_remove+0x4c/0x80
device_release_driver_internal+0x1cc/0x224
device_driver_detach+0x18/0x24
unbind_store+0xb4/0xc0
Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place
it closes the port, before writing to it. The regulator disable is left
unconditional so the controller is still powered down.
The dangling serport->tty that turns this into a use-after-free is
addressed in a separate patch.
Bluetooth: hci_qca: Do not write to the serial port after it is closed
hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP
is set (for example, for the WCN399x family). A failed hci_dev_open_sync()
following a successful qca_setup() calls hdev->close() but not
hdev->shutdown(), so the port is closed while power->vregs_on is left true.
qca_serdev_remove() then passes its power->vregs_on test and calls
qca_power_off(), which writes to the closed port unconditionally.
Seen on a WCN3988 by unbinding the driver after a controller failure. The
trace below is from a 7.0.0 based kernel, where qca_power_off() was still
named qca_power_shutdown():
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000038
Call trace:
tty_set_termios+0x50/0x238 (P)
ttyport_set_baudrate+0x84/0xc0
serdev_device_set_baudrate+0x24/0x40
qca_power_shutdown+0x158/0x1fc [hci_uart]
qca_serdev_remove+0x54/0x68 [hci_uart]
serdev_drv_remove+0x1c/0x2c
device_remove+0x4c/0x80
device_release_driver_internal+0x1cc/0x224
device_driver_detach+0x18/0x24
unbind_store+0xb4/0xc0
Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place
it closes the port, before writing to it. The regulator disable is left
unconditional so the controller is still powered down.
The dangling serport->tty that turns this into a use-after-free is
addressed in a separate patch.
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Tue, 06 Oct 2026 09:00:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_qca: Do not write to the serial port after it is closed hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP is set (for example, for the WCN399x family). A failed hci_dev_open_sync() following a successful qca_setup() calls hdev->close() but not hdev->shutdown(), so the port is closed while power->vregs_on is left true. qca_serdev_remove() then passes its power->vregs_on test and calls qca_power_off(), which writes to the closed port unconditionally. Seen on a WCN3988 by unbinding the driver after a controller failure. The trace below is from a 7.0.0 based kernel, where qca_power_off() was still named qca_power_shutdown(): Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038 Call trace: tty_set_termios+0x50/0x238 (P) ttyport_set_baudrate+0x84/0xc0 serdev_device_set_baudrate+0x24/0x40 qca_power_shutdown+0x158/0x1fc [hci_uart] qca_serdev_remove+0x54/0x68 [hci_uart] serdev_drv_remove+0x1c/0x2c device_remove+0x4c/0x80 device_release_driver_internal+0x1cc/0x224 device_driver_detach+0x18/0x24 unbind_store+0xb4/0xc0 Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place it closes the port, before writing to it. The regulator disable is left unconditional so the controller is still powered down. The dangling serport->tty that turns this into a use-after-free is addressed in a separate patch. | |
| Title | Bluetooth: hci_qca: Do not write to the serial port after it is closed | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2026-10-06T08:45:53.338Z
Reserved: 2026-09-25T10:25:14.336Z
Link: CVE-2026-98294
Vulnrichment
No data.
NVD
Status : Received
Published: 2026-10-06T09:18:19.887
Modified: 2026-10-06T09:18:19.887
Link: CVE-2026-98294
Redhat
No data.
OpenCVE Enrichment
No data.
Weaknesses
No weakness.