Export limit exceeded: 14384 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (14384 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-93076 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: dax/fsdev: clear vmemmap_shift when binding static pgmap Clear pgmap->vmemmap_shift for static DAX devices. When rebinding a static device from device_dax (which may set vmemmap_shift based on alignment) to fsdev_dax, the stale vmemmap_shift persists on the shared pgmap. Explicitly zero it before devm_memremap_pages() so the vmemmap is built for order-0 folios as fsdev requires. | ||||
| CVE-2026-93081 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Fix SCMI device destroy lifetimes scmi_child_dev_find() drops the reference returned by device_find_child() before returning the scmi_device pointer. A concurrent unregister can then release the device while the destroy path is still using the returned pointer. Make the lookup helper return the device_find_child() reference and keep it until scmi_device_destroy() has finished unregistering the child. Also split device_unregister() in __scmi_device_destroy() so the SCMI bus ID is not made reusable until after device_del() has removed the old scmi_dev.N name from sysfs. This avoids a new SCMI device reusing the same ID while the old device is still registered. The final device release callback is also a possible cleanup path when SCMI children are deleted by driver core recursion rather than __scmi_device_destroy(). Release the SCMI bus ID from a common helper used by destroy, register-failure and final-release paths, and clear scmi_dev->id after freeing it so the final release cannot free the same ID again. | ||||
| CVE-2026-92502 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ext4: clear stale xarray tags on folios skipped during writeback In data=journal mode, the writeback thread can hit the WARN_ON_ONCE(sb_rdonly(sb)) in ext4_journal_check_start() while the superblock is being remounted read-only during reboot: Workqueue: writeback wb_workfn (flush-253:0) RIP: 0010:ext4_journal_check_start+0x8b/0xd0 Call Trace: __ext4_journal_start_sb+0x3c/0x1e0 mpage_prepare_extent_to_map+0x4af/0x580 ext4_do_writepages+0x3c0/0x1080 ext4_writepages+0xc8/0x1a0 do_writepages+0xc4/0x180 __writeback_single_inode+0x45/0x2f0 writeback_sb_inodes+0x26b/0x5d0 __writeback_inodes_wb+0x54/0x100 wb_writeback+0x1ac/0x320 wb_workfn+0x394/0x470 And followed by the warning: EXT4-fs warning (device vda1): ext4_evict_inode:195: inode #6263: comm (sd-umount): data will be lost This issue is not reproduced every time, but frequently. The reproduction step is to create a VM with 8 CPUs, 16G memory and setup data=journal: sudo tune2fs -o journal_data /dev/vda1 Run fio: rm -f fiotest fio --name=fiotest --rw=randwrite --bs=4k --runtime=6 --ioengine=libaio --iodepth=256 --numjobs=8 --filename=fiotest --filesize=30G --group_reporting Reboot the VM, and check the console output from: virsh console testvm But there is no dirty inode, folio_clear_dirty_for_io clears PG_dirty but leaves tags PAGECACHE_TAG_DIRTY and PAGECACHE_TAG_TOWRITE set which are only cleared by __folio_start_writeback. In data=journal mode, jbd2 checkpoints the journalled data to its final location and clears its own dirty flag without touching folio PG_dirty or xarray dirty flags. The commit f4a2b42e7891 ("ext4: fix stale xarray tags after writeback") fixes when PG_dirty is still set but there is no dirty page. Another case is PG_dirty is cleared, but PAGECACHE_TAG_DIRTY and PAGECACHE_TAG_TOWRITE is still set. In this case, writeback thread checks clean folio and skips it in mpage_prepare_extent_to_map: if (!folio_test_dirty(folio) || ... folio_unlcok(folio); continue And never reaches ext4_bio_write_folio where the commit f4a2b42e7891 clears the stale xarray tags. Print debug logs after the filesystem is remounted read-only: writepages RDONLY nrpages=2048 dirtytag=1 wbtag=0 towrite=1 sync=0 And all folios are actually clean: folio idx=3 dirty=0 wb=0 checked=0 dirtybuf=0 jbddirty=0 mapped=1 ... We need to clear the xarray stale tags for such clean folios by cycling them through writeback in the skip path, the same way f4a2b42e7891 does in ext4_bio_write_folio. | ||||
| CVE-2026-92503 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ext4: fix ABBA deadlock in ext4_xattr_inode_cache_find() Syzbot/stress-ng reported an ABBA deadlock in ext4 when exercising concurrent xattr workloads (using the ea_inode mount/format option). The deadlock occurs between the running transaction and the eviction thread: - Task 1 (stress-ng): Holds a reference to a shared mbcache_entry (ce) and calls ext4_xattr_inode_cache_find() -> ext4_iget() to retrieve the corresponding EA inode. Since the EA inode is currently being evicted, ext4_iget() blocks in __wait_on_freeing_inode() waiting for eviction to complete. - Task 2 (eviction thread): Currently evicting the same EA inode in ext4_evict_ea_inode(). It calls mb_cache_entry_wait_unused(oe) which blocks waiting for Task 1 to release the reference to the mbcache_entry. To break this deadlock, implement a new ext4_iget() configuration flag named EXT4_IGET_NOWAIT. When set, perform a non-blocking lookup of the inode via VFS's find_inode_nowait() API. If the inode is currently being evicted (marked with I_FREEING or I_WILL_FREE) or created (I_CREATING), or if it is not present in the VFS inode cache (cache miss), simply skip it (returning -ENOENT) rather than waiting for eviction/creation to complete, breaking the ABBA cycle. Since we return -ENOENT immediately on a cache miss, we never attempt to allocate a new inode or call iget_locked(), completely eliminating any TOCTOU race window. If the returned inode is I_NEW, wait for its initialization to clear via wait_on_new_inode(). If initialization fails and the inode is unhashed during wait_on_new_inode() waking up (e.g., due to an I/O read error in another thread), safely drop the reference and return -ENOENT. This unhashed check is executed unconditionally on all cache-hit pathways to properly handle concurrent initialization failures. Finally, standard validation checks (including is_bad_inode, EXT4_EA_INODE_FL, file_acl, and xattr flags) are executed as normal inside check_igot_inode() to fully guarantee VFS-layer safety. In ext4_xattr_inode_cache_find(), invoke ext4_iget() with the new EXT4_IGET_NOWAIT flag to perform the non-blocking cache search. | ||||
| CVE-2026-92515 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Preserve unique-field state across nested structs btf_find_struct_field() initializes a fresh seen mask for every recursive descent. Unique special fields in different levels of the same aggregate therefore do not see one another. The duplicate fields can reach btf_parse_fields(), where they trigger an invariant WARN_ON_ONCE(). A crafted user BTF can consequently trigger the warning before map creation checks capabilities. Initialize the seen mask once in btf_find_field() and pass the same pointer through struct, datasec, and nested-struct walks. This gives the entire field traversal one shared uniqueness state. | ||||
| CVE-2026-90428 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: iommu/tegra241-cmdqv: Don't run the error ISR before probe sets up vintfs __tegra241_cmdqv_probe() requests the error IRQ before it has allocated the cmdqv->vintfs array and set cmdqv->num_vintfs. A CMDQV left enabled with a latched error across a kexec fires the IRQ as soon as it is requested, and tegra241_cmdqv_isr() then walks the uninitialized cmdqv->vintfs array. Request the IRQ only after cmdqv->vintfs is allocated and zeroed, so that a latched interrupt firing early runs the ISR against a valid array of NULL slots that it safely skips. | ||||
| CVE-2026-90359 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Reject >8 byte return values on return-reading trampoline paths btf_distill_func_proto() builds the function model used for the fentry/fexit/fmod_ret/fsession trampolines and struct_ops. It has accepted a 16-byte __int128 return value since the trampoline was introduced: __get_type_size() returns the integer's type size, and the return-type check only rejected ret < 0. But the BPF trampoline preserves only 8 bytes of the return value (RAX on x86, i.e. R0). For an attach type that reads the target's return value the second half (RDX / R3) is neither saved nor restored, so a program attached to a function returning a 16-byte value corrupts the value seen by the real caller and itself observes only half of it. struct_ops trampolines have the same limitation. This affects the attach types that read the target's return value: fexit, fmod_ret and fsession (plus the _multi variants of fexit and fsession), and struct_ops. fentry/fentry_multi run before the target returns and are unaffected. Reject a >8 byte return value for these attach types in bpf_check_attach_target() and bpf_check_attach_btf_id_multi(), and for struct_ops in bpf_struct_ops_desc_init(). | ||||
| CVE-2026-90370 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: bound TLV walk in mt7996_mcu_get_chip_config The response TLV loop advanced by tlv->len without a minimum, so a theoretical firmware response containing a zero-length TLV could spin forever, hanging the CPU during device probe. The u32 payload was also read without bounds checking. Reject a short fixed field, stop on a TLV whose length underruns the header or overruns the skb. | ||||
| CVE-2026-90386 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: i3c: dw: avoid shift-out-of-bounds when DAA assigns no devices On an empty bus ENTDAA assigns nothing, so cmd->rx_len (the count of addresses left unassigned) equals master->maxdevs. The GENMASK() index master->maxdevs - cmd->rx_len - 1 then becomes -1, which trips up UBSAN. This happens every time on boot on a Gigabyte/AMD server: UBSAN: shift-out-of-bounds in drivers/i3c/master/dw-i3c-master.c:905:12 shift exponent 64 is too large for 64-bit type 'long unsigned int' CPU: 7 UID: 0 PID: 963 Comm: (udev-worker) Not tainted 7.0.11-200.fc44.x86_64 #1 PREEMPT(lazy) Hardware name: Giga Computing E163-Z34-AAH1-000/MZ33-DC1-000, BIOS R32_F45 04/01/2026 Call Trace: <TASK> dump_stack_lvl+0x5d/0x80 ubsan_epilogue+0x5/0x2b __ubsan_handle_shift_out_of_bounds.cold+0xd7/0x1ab dw_i3c_master_daa.cold+0x1b/0x96 [dw_i3c_master] i3c_master_do_daa_ext.part.0+0x3e/0xf0 [i3c] Skip the mask when no new device was assigned. | ||||
| CVE-2026-90390 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: md/bitmap: resume array on backlog_store() error path backlog_store() suspends the array before checking whether a write-mostly device exists. If no such device exists, the error path only unlocks reconfig_mutex and leaves the array suspended, blocking subsequent I/O. Use mddev_unlock_and_resume() to release both states. | ||||
| CVE-2026-90333 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: dm-integrity: replace forgeable discard filler with a keyed sector marker The discard-block check in dm_integrity_rw_tag() treats a stored tag of all 0xf6 bytes (DISCARD_FILLER) as proof a block was discarded and skips HMAC verification. allow_discards is only accepted in dm-integrity's standalone mode. An attacker with raw write access to the backing device, but without the integrity key, can stamp any block with an all-0xf6 tag and have it served as authentic. Add a new "allow_discards_keyed" target argument that marks discarded blocks with a keyed checksum of (salt || sector) instead, computed by integrity_discard_checksum(). | ||||
| CVE-2026-90355 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: clear stale link state on full reset After a full chip reset, mac80211 reconfig replays interface, link and channel context setup. mt7996_vif_link_add() short-circuits when the link_id is still marked in mvif->valid_links, a state introduced for postponing link teardown to interface removal. The reset path frees the link structures without clearing those bits, so the replayed setup never re-creates dev_info/bss_info/STA records in the restarted firmware and never re-registers the link wcid, leaving the device inoperative. The reset path also leaks every allocated MLD index: per-link indices and the per-vif group/remap indices are re-allocated from scratch during reconfig, but the old bits stay set in the masks, so repeated full resets exhaust the index space. Clear valid_links in the reset vif iterator and reset the MLD index masks alongside the existing omac_mask clearing. | ||||
| CVE-2026-90282 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: phy: qcom: qmp-usb-legacy: Fix possible NULL-deref on early runtime suspend There is a small window where the runtime suspend callback may run after pm_runtime_enable() and before pm_runtime_forbid(). In this case, a crash occurs because runtime suspend/resume dereferences qmp->phy pointer, which is not yet initialized: `if (!qmp->phy->init_count) {` This can also happen if user re-enables runtime-pm via the sysfs attribute before qmp phy is initialized. Similarly to other qcom phy drivers, introduce a qmp->phy_initialized variable that can be used to avoid relying on the possibly uninitialized phy pointer. | ||||
| CVE-2026-90304 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ARM: 9484/1: enable interrupts when unhandled user faults are triggered PREEMPT_RT requires interrupts to be enabled when sending signals. When do_DataAbort()/do_PrefetchAbort() triggers unhandled user faults, that is `inf->fn()` return a non-zero value, and the interrupts are not enabled within the hook function, force_sig_fault() will be called with interrupts disabled. This can be triggered by user programs executing the bkpt instruction, with kernel config CONFIG_PERF_EVENTS=n. Enable interrupts in do_DataAbort()/do_PrefetchAbort() when unhandled user faults are triggered to fix the issue. | ||||
| CVE-2026-90236 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: NFSD: Release the export reference when reaping open stateids nfs4_put_stid() releases the svc_export tracked in nfs4_stid.sc_export, but free_ol_stateid_reaplist() frees open and lock stateids by calling ->sc_free() directly, bypassing that path. An open stateid takes an sc_export reference in nfs4_open() and a lock stateid takes its own in init_lock_stateid(); both reach free_ol_stateid_reaplist() through their normal teardown, the open stateid via release_open_stateid() and the lock stateid via nfsd4_release_lockowner(), each through put_ol_stateid_locked(). The reference is therefore never dropped, pinning the export and blocking unmount for the lifetime of the stateid. Release sc_export in free_ol_stateid_reaplist() the way nfs4_put_stid() does. ->sc_free() runs once per stateid, and a stateid reaches free_ol_stateid_reaplist() or nfs4_put_stid() but never both, so the reference is dropped exactly once. Revoked stateids reach this path with sc_export already cleared by drop_stid_export(), so they are skipped rather than double-freed. nfs4_put_stid() itself read sc_export before acquiring cl_lock. drop_stid_export() clears that field and releases the reference under cl_lock, so a concurrent revocation could drop the export in the window between the read and the final put, releasing the same reference twice. Read sc_export while cl_lock is held so the two paths serialize and the reference is released exactly once. | ||||
| CVE-2026-90311 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: thermal: hwmon: Remove hwmon class device along with its parent The current code creates one hwmon device per thermal zone type and that device is registered under the first thermal zone of the given type. That turns out to be problematic when the thermal zone holding the hwmon device is removed. For example, say that there are two ACPI thermal zones on a system /sys/devices/virtual/thermal/thermal_zone0/ /sys/devices/virtual/thermal/thermal_zone1/ The current code registers a hwmon class device for thermal_zone0 only: /sys/devices/virtual/thermal/thermal_zone0/hwmon0/ because the type is "acpitz" for both of them, but it adds a sysfs attribute that belongs to thermal_zone1 under it: /sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp2_input There is also /sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp1_input which belongs to thermal_zone0. When thermal_zone0 is removed, say because the ACPI thermal driver is unbound from the underlying platform device, thermal_remove_hwmon_sysfs() skips the removal of hwmon0 because of the temp2_input attribute belonging to thermal_zone1 which effectively prevents thermal_zone0 removal from making progress. Address this by making thermal_remove_hwmon_sysfs() remove the entire hwmon class device interface for the given thermal zone type when the thermal zone device holding it is removed. To prevent races with thermal_add_hwmon_sysfs() that may interfere with this, carry out the entire addition and removal of hwmon sysfs interfaces for thermal zones under thermal_hwmon_list_lock. Also adjust the layout of the labels in thermal_add_hwmon_sysfs() to the current kernel coding style to align with the new "unlock" label. | ||||
| CVE-2026-90195 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: riscv, bpf: Fix missing sign-ext for signed 1-byte and 2-byte kfunc args On RV64, the ABI requires sign-extension for signed 1-byte and 2-byte kfunc args. However, the RV64 JIT currently does not perform sign-extension for such kfunc args. Before commit 7ce090afbf72 ("bpf: Infer zext_dst based on static register liveness analysis"), state pruning could potentially omit zero-extension of 32-bit subregisters, which inadvertently masked the above issue by making the args appear as if they had been properly sign-extended. After that commit, the problem is exposed, causing the kfunc_call/kfunc_call_test4 selftest to fail. Fix this by extending the existing sign-extension logic to handle signed 1-byte and 2-byte kfunc args as well. | ||||
| CVE-2026-92944 | 1 Patriksimek | 1 Vm2 | 2026-09-19 | 9.8 Critical |
| vm2 versions 3.10.2 through 3.11.6 contain a sandbox escape vulnerability on Node.js 26 where Promise.prototype.finally() bypasses vm2's wrapper protections due to a stale PromiseThenLookupChain protector in V8 14.6. Attackers can exploit this by creating an async function that returns a Promise with an attacker-controlled constructor Symbol.species, allowing them to reach the host Function constructor and process object for arbitrary code execution. | ||||
| CVE-2026-92938 | 1 Patriksimek | 1 Vm2 | 2026-09-19 | 9.9 Critical |
| vm2 versions 3.11.3 through 3.11.6 expose Node.js's host node:sqlite module to code running in NodeVM when that builtin is permitted, either explicitly or through builtin: ['*']. The module is wrapped with vm.readonly(), which prevents property assignment but leaves host-authority callables reachable; in addition, the resolver treats any request starting with 'node:' as a core-module request and the runtime strips only one 'node:' prefix, so a sandbox request for 'node:node:sqlite' resolves to the configured node:sqlite entry. Sandboxed code can therefore create an in-memory DatabaseSync with extension loading enabled and call DatabaseSync.loadExtension() on a native library bundled in the untrusted plugin package (path derived from __dirname). SQLite loads the library into the Node.js host process and invokes its native entry point, giving the sandboxed plugin arbitrary native code execution outside the sandbox with the host process's privileges. The issue is fixed in vm2 3.11.7. | ||||
| CVE-2026-90212 | 1 Linux | 1 Linux Kernel | 2026-09-19 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: arm64/efi: Avoid voluntary preemption with efi_mm installed Gus reports a bad kernel memory access when using software PAN (CONFIG_ARM64_SW_TTBR0_PAN=y) on a machine with support for EFI runtime services: Unable to handle kernel access to user memory outside uaccess routines at virtual address 00000000f322ff30 Mem abort info: ESR = 0x0000000096000004 FSC = 0x04: level 0 translation fault Internal error: Oops: 0000000096000004 [#1] SMP Workqueue: efi_rts_wq efi_call_rts pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : efi_call_rts+0xd8/0x288 Call trace: efi_call_rts+0xd8/0x288 (P) process_one_work+0x178/0x4f8 worker_thread+0x194/0x328 This is because the fpsimd context management code called from __efi_fpsimd_begin() can preempt voluntarily, returning later to the EFI code with an incorrect value for TTBR0_EL1 thanks to the deferred mm switching used by the software PAN implementation. Since EFI runtime services cannot preempt voluntarily and because the fpsimd switching code does not rely on the TTBR0_EL1 mappings, simply reorder the fpsimd switch so that it occurs before we change the page-table. | ||||